Monday, June 28, 2010

Embroidery hoop framing tutorial

This was originally posted on my Polka and Bloom blog. Yup! Polka and Bloom now has its own website, with a blog and everything! :-)

This is what you will need:
Your embroidered piece
A hoop which will fit your embroidery
Felt in the same colour as your embroidered cloth (or as close as possible)
Heavy card stock. I used acid free watercolour paper

Glue that dries clear. I used a gel glue, which worked really well
Embroidery thread in the same colour as your cloth + needle
Scissors

Cut a circle of felt and one of the card stock, they should be the size of the inside of the inner hoop.


Put your cloth on top of the inner hoop and move it around until it is perfectly positioned. Then slide the outer hoop on top.


Remove both hoops and now you have an imprint of how to position the cloth. This is handy, because depending on the glue you are using you will probably have to be quick once you  have applied the glue to the hoops.

Which is the next step. No picture of that (sorry), but there was no time what with the glue drying and stuff.

This is what you do: apply glue to the outside of the inner hoop, then place your cloth on top, using the imprint as a guide. Then apply glue to the inside of the outer hoop and slide it in place over the cloth and inner hoop. Tighten the screw slightly and then pull the cloth taut as you go around the hoop. Once the cloth is evenly taut, tighten the screw properly.


Your cloth and hoop combo should now look something like this.


Your cloth is hopefully quite a bit wider than the hoop, if it isn't you may be slightly buggered. Anyway. Cut the cloth into a circle that is about 5cm/2" wider than the hoop.

Then place the felt circle inside the hoop. There is no need to sew or glue it into place. It is there to protect the stitches and make everything look neat. Especially if your cloth is light.


Now thread your needle with a length of thread that is the size of the circumference of the hoop + 15cm/6". Gather the edge like you would if you were making a yoyo. You want the stitches to be as even as you can and also quite close together, so you get a neat end result.


Which hopefully looks something like this. Pull the thread tight and finish by making a couple of knots in the fabric. The thread/fabric should be so tight that the fabric 'hovers' slightly in the middle, not touching the felt.


Now apply glue to your card stock, be quite generous, but not to the point of soaking the card stock! Also apply some glue to the fabric. Not a lot, just enough to add a bit of extra bonding with the card stock.


Place the card circle in the hoop and press it down firmly all over.


Place something heavy on top. Preferably something that has a flat bottom and covers most of the inside of the hoop. Leave like this for about half an hour, then remove the heavy weight and leave to dry completely.

My set up here is not quite ideal, would have been better if the diameter had been a bit wider. But hey, you work with what you've got, eh?

Tie a nice piece of ribbon or string to the closure of the hoop and hang on your wall.

Additional-
If you want to be able to remove your embroidered cloth from the hoop at some point, skip any steps to do with glue. In stead of finishing it off with card stock, you can stitch a second felt circle onto the 'yoyo' of the back.

Also, it may be a good idea to wrap the inner hoop in fabric strips like bias binding or similar, which will protect the cloth from wear to some extent. It will add bulk to the ensemble,  though.

10 comments:

Sarah said...

Thanks for sharing this, I've been wondering how to do that. Any tips on a good source for nice frame-worthy hoops?

Pumpkin said...

Mine have never looked this neat but they will from now on. Thanks for the tips. Also, if you have a response to the question above about frame-worthy hoops, I'd love to hear the answer too. Thanks!

Nichole said...

Finally, I have been forever trying to find a tutorial on this, thanks!

jkc said...

I have been looking for a tutorial on this...thanks, this looks perfect!

JacqueLynn said...

excellent tutorial and boy is it going to be handy - I never knew how to do this before. THANKS

edythe o. said...

Thank you so much for this. It seems easy to do and preserves the simple look of embroidery in a hoop. (I only wish I had seen it before I gave friends a piece i did for them--in the hoop but sans any framing. Doh!)

Holli Yeoh said...

Great tutorial and what a perfect way to frame an embroidery project. It makes me want to start stitching again!

pam said...

You have done a great job with this tutorial. I have been wondering how to create a frame using a hoop and now you have beautifully answered my question!

Thank you!

Carina said...

Thank you all very much! I am so glad you like the tutorial!

@Sarah + Pumpkin
I think nice wood hoops are, well, nice. Some plastic ones with woodgrain look would be good too.

Also, if you have plain ones, you can always paint them in a colour that goes with your stitched project. You could even paint them with blackboard paint so you can write little messages on the hoop!

Casey said...

thank you for this! I've been wondering how to do this and make the picture still look good

Please write comments in English - or any of the languages below. For other languages than these I won't be able to tell if the comment is nasty or spam, so I'll have to delete it. I don't want to delete legitimate comments! Thank you for understanding! xo, Carina

Languages I can read: Danish, German, French, Italian, Spanish, Swedish, Norwegian, Dutch.
Related Posts Plugin for WordPress, Blogger...